|
 |
DMC
Pentium III 6U VME Processor Module with Dual PMC
  
|
Features
- Provides Maximum VME Single-Slot Functionality
- Pentium III or Celeron support
- Standard front panel I/O
- Tundra Universe IID PCI-VMEbus interface provides
64-bit VMEbus
- One or two Intel 82559 single chip Ethernet controllers
|
|
|
Additional Photos
DMC Block Diagram |
|
Technical Specifications
| System Architecture |
Pentium III or Celeron
Standard front
panel I/O includes SVGA, 10/100BaseT and mouse/keyboard
Two PMC sites in a single slot for maximum flexibility
An IDE, floppy drive interface second LAN port,
USB, game port, COM1/2, LPT1, and other standard PC I/O
are routed to a rear plug-in expansion card behind the backplane
(IDE and floppy also available on-board)
PMC ports accessible from front panel or rear
Optional transition board provides hard drive and either
floppy or CD-ROM drive in adjoining slot (total of two slots
with both boards) and includes second 10/100BaseTX interface |
| CPU support |
Socket 370 processor
1..2 GHz
Pentium III standard version (other processors can be quoted) |
| Chip Set |
Intel 815E
Built-in 3D Graphics with resolutions up to 1600
x 1200
Ultra ATA 100/66/33 IDE protocol
Chipset includes: DRAM controller, PCI bus arbitration
logic and interface, USB interface, RTC, NV-RAM, Soundcard
interface, standard PC timers, Ultra DMA, and interrupt
logic
Optimized SDRAM support |
| Single Slot |
Single-slot VMEbus operation with on-board
CompactFlash disk for bootable mass storage |
| DRAM |
SO-DIMM module for 3.3 V PC133 SDRAM of up to
512 MB |
| BIOS |
General Software's flash-based system BIOS
Upgradeable via floppy
BIOS can be customized
to customer specifications |
| VMEbus |
Tundra Universe IID PCI-VMEbus interface provides 64-bit
VMEbus transfer rates over 30 MB/sec
FIFOs
permit write-posting to maximize available PCI and VMEbus
bandwidth
Full Slot 1 (system controller)
functions provided
Lower cost versions available
without VMEbus |
| PMC Expansion |
Two PMC expansion slots available on DMC
I/O is routed out to the P0 and P2 connectors on the VMEbus
Optional three-PMC carrier supports four PMC cards
in two-slot configuration with the DMC (three-slot configuration
with Transition Module)
Dynatem offers a
broad range of PMC modules including communication boards,
graphics, imaging, DSP and I/O |
| Ethernet |
One or two Intel 82559 single chip Ethernet controllers,
one port acces sible at the front panel, while the other
is routed to the P0 connector on the VMEbus (versions without
P0 have only one 82559)
10BaseT/100BaseTX
support, full duplex |
| IDE Support |
Primary Ultra DMA IDE interface with improved transfer
rates is accessible from an on-board 44-pin header
PIO and bus master support
Secondary
IDE port is routed to a Type II compatible CompactFlash
connector for on-board booting via flash- based and mechanical
storage |
| Floppy Support |
Floppy drive controller, with support for drives up to
2.88 MB |
| SVGA |
Built-in 3D Graphics with resolutions up to 1600 x 1200 |
| CompactFlash |
Support for up to 1 GB solid-state CompactFlash or 1 GB
MicroDrive |
| Watchdog |
Programmable watchdog timer for system recovery |
| Front Panel I/O |
VGA(MDSM), keyboard/mouse(MDSM), one 10/100BaseTX port
(RJ-45), front panel I/O for the two PMC modules
MDSM adapter cables are provided |
| Rear I/O Expansion |
COM1 (routed through P2) and COM2 (routed through P0)
are both RS-232 ports based on a 16C550 compatible UART
with 16-byte transmit and receive FIFO's
Second 10/100BaseTX port (routed through P2)
IDE (routed through P2)
LPT1 (routed through
P2)
Floppy Disk Interfaces (outer rows of
the VME64 P2 connector)
Keyboard/mouse (routed
through P0 and also available on front panel)
Dual USB ports (routed through P0)
AC '97
sound port (routed through P0)
Game port
(routed through P0)
IR port (routed through
P0)
PMC I/O (one site is routed to the outer
rows of P2 connector while the other site is routed to the
P0 connector)
XMCPTB rear I/O interface board
provides industry standard connectors for all rear I/O
The DMC is also available without P0 connector |
| TBM Transition Board |
Transition board requires one additional slot for a two-slot
configuration with the DMC, including floppy or CD-ROM drive,
and hard drive
Includes a front panel COM1
and LAN2 (second 10/100BasTX port) connectors |
| Software |
Board support packages available for NT, Linux, QNX, VxWorks
Additional software available upon request |
| Dimensions |
233.5 mm (L) x 160 mm (W) |
Ordering Insformation
| Part# |
Description |
| XMCxN9x |
CPU board with 1.2 GHz Celeron, two 10/100Base-TX ports, SVGA video, 2
COM ports, two PMC expansion slots, KB, mouse, bi-directional parallel I/O,
single slot, and 256 MB SDRAM. Supports CompactFlash. With BIOS |
| XMCQxxx |
256 MB Flash for DMC |
| XMCRxxx |
512 MB Flash for DMC |
| XMCSxxx |
1 GB Flash for DMC |
| xMCTxxxx |
2 GB Flash for DMC |
| xMCUxxxx |
4 GB Flash for DMC |
| XMCxPxx |
Upgrade to 512 MB DRAM |
| XMCxxNx |
Upgrade to 1.2 GHz Pentium III |
| XMCxxxP |
With P0 connector and support for two 10/100BaseT ports (physical interface
for second Ethernet port resides XMCPTB) |
| DMCxxxx |
With VMEbus |
Support Hardware
| TBMtuuvEyz |
Transition board for XMC with 40-pin IDE connector, front
panel COM port, 26-pin header for printer port, LAN2 second
10/100BaseT interface, and options as listed below. |
Transition Board Option
| t = F |
1.44 MB floppy drive installed on Transition Board |
| t = C |
CD-ROM drive in place of floppy drive |
| t = t |
Neither floppy drive nor CD-ROM drive installed on Transition
Board |
| uu = 20 |
20 GB IDE hard disk drive installed |
| uu = 40 |
20 GB IDE hard disk drive installed |
| uu = 20 |
No IDE hard drive installed |
| v = T |
Transition board mounted on top of SBC (socket on bottom) |
| v = B |
Transition board mounted on bottom of SBC (socket on top) |
| v = v |
Transition board interface via P2 to P2 cabling only, no
direct socketed connection (separate single-slot front panels
fror SBC and transition board) |
| y = G |
Gasketed front panel (not available in all configurations) |
| y = y |
Non gasketed front panel (default) |
| z = S |
Single-slot front panel, can be separated from CPU board |
| z = D |
Double-wide front panel for SBC and transition board |
| XMCPTB |
Rear plug-in board for XMC provides connectors for: COM1, LAN2, LPT1,
IDE, Floppy Drive interface, and a speaker. One 64-pin DIN header for I/O
expansion for one PMC module. Uses 5-row P1 and P2 connectors. No P0 connector. |
| XMCPTBN |
Same as XMCPTB but without PMC I/O connector
and with 3-row P1 and P2 (no P0 connector) |
| XMCPTBP |
XMCPTB with the following additional features: a P0 connector and I/O
connectors for audio, USB (x2), KB/Mouse, Game port, infrared port and a
64-pin DIN header for I/O expansion of the second PMC site. |
| XPMC3 |
Carrier for 3 PMC cards (requires additional slot) |
DMC Software
| DSW-500- DMC |
VxWorks Tornado BSP (one time charge includes upgrades) |
| DSW-700-DMC |
Drive VME, a high performance VME to Windows/NT Systems Software Link
(Development version). Windows XP also supported |
| DSW-701-DMC |
Run-time copy of Drive VME |
| DSW-WINNT |
Windows NT |
| DSW-WIN2000 |
Windows 2000 |
| DSW-WINXP |
WindowsXP |
| DSW-800-DMC |
BSP for Lynx-OS (includes BSP support) |
| DSW-900-DMC |
BSP for QNX (includes BSP support) |
| DSW-A00-DMC |
BSP for Solaris |
| DSW-B00-DMC |
BSP for Linux (includes Redhat operating system) |
back to top
|
|
|
